drukalo
Print-ready files8 min read12 February 2026Updated 9 June 2026

How to add bleed to a print design - Canva, Figma, Illustrator, InDesign

A practical guide: how to add bleed in Canva, Figma, Adobe Illustrator and InDesign. Bleed sizes for different formats. The most common mistakes and how to avoid them.

bleedprint bleedCanvaFigmaIllustratorInDesign

Bleed is the part of a design that gets trimmed off after printing - it exists so the guillotine doesn't leave white slivers along the edges. The standard in Polish print shops is 3 mm of bleed on each side. In this guide we show you, step by step, how to set up bleed in the four most popular programs: Canva, Figma, Adobe Illustrator and InDesign.

What bleed is and why you need it

When a print shop prints your design, it does so on a sheet larger than the final format. The guillotine then trims the edges down to the trim size. Because of mechanical tolerances, the guillotine may cut slightly more or less than the exact trim size (typically ±0.5–1 mm). Without bleed, the result is this: if the guillotine cuts 0.5 mm more than planned, a white strip (the colour of the paper, not your design) appears along the edge.

Bleed solves the problem. You add an "extra" 3 mm of design beyond the trim size. After trimming, the guillotine can cut a little more or less - and the edge still shows your design, not white paper. Every graphic element that runs to the edge (backgrounds, photos, coloured blocks) must extend all the way to the outer edge of the bleed.

Standard bleed sizes

ProductTrim sizeBleedSize with bleed
Standard business card85 × 55 mm3 mm91 × 61 mm
DL flyer100 × 210 mm3 mm106 × 216 mm
A6 flyer105 × 148 mm3 mm111 × 154 mm
A5 flyer148 × 210 mm3 mm154 × 216 mm
A4 flyer210 × 297 mm3 mm216 × 303 mm
A3 poster297 × 420 mm3 mm303 × 426 mm
A2 poster420 × 594 mm3 mm426 × 600 mm
A1 poster594 × 841 mm3 mm600 × 847 mm
B1 poster707 × 1000 mm5 mm717 × 1010 mm
A0 poster841 × 1189 mm5 mm851 × 1199 mm
Bleed for different print formats

For large format (B1, A0, roll-up banners), some print shops require more bleed (5–10 mm). At drukalo the standard is 3 mm for all formats up to A1 and 5 mm for B1, A0 and roll-ups. Any design with less bleed is flagged during preflight and we get back to the customer asking for a correction.

Bleed in Canva - step by step

Canva is the most popular tool among freelancers and micro-businesses. Bleed is available only in Canva Pro/Teams - in Canva Free you have to add it manually (which is fiddly). We recommend upgrading to Canva Pro (about 40 PLN a month) or switching to Affinity - since late 2025, after Canva acquired Serif, the app has been free and offers full prepress support, which makes it better for print.

  1. Choose a document size matching the trim size (e.g. A5 for an A5 flyer)
  2. In the top menu click "File" → "Settings" → enable "Show margins and print bleed"
  3. Extend every background element (coloured blocks, photos) to the edge of the bleed area (the dashed red line)
  4. Keep text and key elements inside the safe margins (the dashed green line)
  5. When exporting, choose "PDF for printing" → tick "Crop marks and bleed"
  6. Check the exported PDF - there should be 3 mm of bleed around the whole design

Bleed in Figma - a workaround

Figma has no native bleed support - it's a tool for product and UI design, not prepress. You can work with bleed manually, but the final PDF has to be prepared in Adobe Illustrator or Affinity Publisher. For print-only projects, Figma isn't the best choice.

If you have to work in Figma (e.g. you rely on your company's component library), here's how:

  1. Create a Frame at the size including bleed - e.g. 154 × 216 mm for A5
  2. Inside the frame, add a centred helper rectangle at the trim size (148 × 210 mm) - it marks the trim boundary
  3. Extend background elements to the edges of the frame (beyond the helper rectangle)
  4. Keep text inside the helper rectangle with an additional 4–5 mm safe margin
  5. Before exporting, delete the helper rectangle and export as PNG/PDF
  6. Open the file in Illustrator, add crop marks and save as PDF/X-4

Bleed in Adobe Illustrator

Adobe Illustrator is the prepress standard for vector-based designs. You set bleed when creating the document or in the document settings.

Creating a new document with bleed

  1. File → New
  2. Pick a preset or enter the trim dimensions (e.g. A5: 148 × 210 mm)
  3. In the "Bleed" section enter 3 mm (or 5 mm for large format)
  4. Click "Create"
  5. On the artboard you'll see a red line - that's the bleed boundary
  6. The black line inside is the trim boundary (the final format)

Exporting a PDF with bleed

  1. File → Save As
  2. Choose the "Adobe PDF (.pdf)" format
  3. In the Save Adobe PDF window choose the "[PDF/X-4:2008]" preset
  4. In the "Marks and Bleeds" tab tick "Use Document Bleed Settings" (or enter 3 mm manually)
  5. Optionally tick "Crop Marks" (trim marks for the operator)
  6. Click "Save PDF"

Bleed in Adobe InDesign

Adobe InDesign is the standard for multi-page projects (brochures, books, magazines). You set bleed the same way as in Illustrator.

  1. File → New → Document
  2. Choose the format (e.g. A5)
  3. In the "Bleed and Slug" section enter 3 mm for each edge (or untick "make all settings the same" if you need different values)
  4. Click "Create"
  5. On the page you'll see two lines: black (trim) and red (bleed)
  6. To export: File → Export → PDF (Print) → preset [PDF/X-4:2008]
  7. In the "Marks and Bleeds" tab tick "Use Document Bleed Settings" and "Crop Marks"

Bleed in Affinity (a free alternative)

Affinity (Designer, Photo and Publisher combined) is Adobe InDesign's competitor. Since late 2025, after Canva acquired Serif, the app has been free - previously it cost a one-off of about 250 PLN, which was still cheaper than an Adobe subscription (100+ PLN a month). Full prepress support, bleed, PDF/X-4. It works almost exactly like InDesign:

  1. File → New → Print → choose the format
  2. In the "Bleed" section enter 3 mm
  3. Click "Create"
  4. Export: File → Export → PDF → preset "PDF (Press)" → Settings → Bleed: Use document bleed → Include crop marks
  5. Save

The most common bleed mistakes

MistakeConsequenceFix
No bleedWhite slivers along the edgesAdd 3 mm of bleed in the document settings
Bleed under 3 mmWhite slivers at the slightest guillotine deviationIncrease to 3 mm
Bleed over 5 mmWasted space, possible imposition issuesStick to 3–5 mm
Text in the bleed areaText cut off after printingMove the text into the safe zone
Background stops short of the bleedWhite slivers where the background endsExtend the background to the edge of the bleed
Crop marks inside the designVisible marks on the finished productAdd crop marks only on export
Typical mistakes and their consequences

Frequently asked questions

  • Can I leave out bleed if my design has a white background?
    Technically yes - if the entire background is white (or the colour of the paper), missing bleed won't cause a visible problem. But it's risky: if you slip up and add a coloured element near the edge (e.g. a border), you'll get a white strip without bleed. It's better to always add 3 mm of bleed as a safe standard, even for designs with a white background.
  • How much bleed for a book cover with a spine?
    Standard bleed (3 mm) on every outer edge (top, bottom, left, right). The spine is the exception - there's no bleed there (the spine is formed by folding between the two covers, not by trimming). Perfect-bound cover file: width = back cover + spine + front cover, with 3 mm of bleed at the top/bottom and 3 mm on the left (on the left cover) and the right (on the right cover). No bleed on the spine.
  • What if my print shop requires 5 mm of bleed?
    Some large-format printers (B1 and A0 posters, roll-ups) require 5–10 mm of bleed because of bigger guillotine tolerances on large formats. Check the print shop's requirements before you start designing. drukalo's standard is 3 mm up to A1 and 5 mm for B1 and larger. If your design was built with 3 mm and the printer wants 5 mm, just change the document settings in Illustrator/InDesign and extend the backgrounds again.
  • Do business cards need bleed?
    Yes, 3 mm. Business cards are cut on a guillotine with the same tolerances as other products. An 85×55 mm card = a 91×61 mm design with bleed. If you only design to the trim size, white slivers may appear on the edges. The print shop will send the file back asking for a correction.
  • Can I use Photoshop for print designs?
    Yes, but only for designs dominated by raster artwork (photos, colour gradients). Photoshop creates bitmap images - they lose quality when scaled. For business cards, text-heavy flyers and posters we recommend Illustrator (vectors) or InDesign (a mix of vectors and raster). In Photoshop you add bleed like this: Image → Canvas Size → increase the dimensions by 6 mm (3 mm × 2 sides).
  • Does bleed affect the print price?
    No. The print shop uses a larger sheet whether you add bleed or not - the price depends on the trim size and quantity, not on bleed. Without bleed you simply risk white slivers at the edges. With bleed you can be sure the design prints correctly.
  • Are 'safe zone' and 'bleed' the same thing?
    No. The safe zone is the area inside the trim size where all key elements should sit (text, logo, phone number). Bleed is the area outside the trim size where backgrounds and graphics that run to the edge should extend. Standard: 3 mm of bleed outwards, a 4–7 mm safe zone inwards from the trim edge. Together they give you a safe layout margin.

Related products

Order the products from this article

Read more in “Print-ready files”